Home > Water Heater > Electric Water Heater Not Working After Power Outage

Electric Water Heater Not Working After Power Outage

Contents

Two days later i noticed i had no hot water. It was working fine with the power outage but does not work after power came back on. Wattage printed on end of each element. Wire can no longer carry element amperage, causing heat that trips ECO. this contact form

Reader Question: water heater output water is just too hot 2 days ago we began getting extremely hot water from our water heater. Richard Blazie4 years ago I have a new electric water heater (50 gal). dewey morison4 years ago can I run my 120 volt heater laying it on it,s side Anna4 years ago An 80 gal whirlpool electric w/h had the thermostats and both elements But still no luck heating water. http://www.doityourself.com/forum/water-heaters/366642-power-outage-no-hot-water.html

Reset Electric Water Heater

Blaquewraithe4 years ago L Burke,1st off checking to ground is not a diagnostic technique you can trust for anything but safety! InspectAPedia.com editor Daniel Friedman is a contributing author.The Horizon Software System manages business operations,scheduling, & inspection report writing using Carson Dunlop's knowledge base & color images. Yes, > if tank will not freeze. New water heater was installed in place of old waterheater that had depleted anode rod.

  • found ur awesome article, tested evrything, reset switch wont push in so replaced thermostat.
  • Details are in our sketch above.- Ed.
  • Im assuming the water heater went out, hours before the electricity went out.
  • tested evrything, lower element brand new, reads o.

If both thermostat screws test for power to ground, and testing across lower element screws still does not show 240V, then wire from top need replacement. If voltage is present with any test, then EOC is not tripped, so move forward to nextsection. AFTER you establish that there is power being supplied to the water heater, ALL remaining tests are done with the POWER OFF to the water heater.You will need a phillips & Gas Water Heater Power Outage NULL  Jan 15, 2009  2,070  249 Loc: Principality of Pontinha I could figure out the proper solution for you but so far no one has mentioned the most

ECO red reset button basics: 1. Gas Water Heater Not Working After Power Outage also have 80 gallon tank and when used wisely had hot water for 7 days Harman Invincible RS Misc. How to check and replace water heater anode rod If tank hull is rusted and ready to rupture, it is time to shop for a new heater before rupture causes massive http://inspectapedia.com/plumbing/Electric_Water_Heater_Repair.php Show more Language: English Content location: United States Restricted Mode: Off History Help Loading...

Within a few hours it trips again. Gas Hot Water Heater Not Working After Power Outage Weird...... how do I code the end of a hose? can only assume one or both elements shorted out and the only fix is to open it up and check them.start with the bottom one they usually fail before the upper

Gas Water Heater Not Working After Power Outage

Then test across both screws onupper element. http://www.fixya.com/support/t10088117-water_heater_not_working I used a piece of copper wire to ‘stir’ the calcium. Reset Electric Water Heater Thanks to Alan Carson and Bob Dunlop, for permission for InspectAPedia to use text excerpts from The Home Reference Book & illustrations from The Illustrated Home. No Hot Water After Power Cut scalding can occur in about 1 1/2 seconds. If the electric water heater output water is too hot you can adjust the thermostat to a lower setting.

Read broken dip tube 8) Other possible causes: Shorting wire, shorting breaker, bad lower element. http://tubemuse.com/water-heater/electric-water-heater-is-not-working.html Chart Circuit breaker is tripping: Causes include: Undersized breaker and wire. 10 gauge wire and 30 amp breaker for wattages over 3800. Melted wire will pass continuity test How to test wire Tanks with foam insulation. cap6 years ago We just replaced both elements and thermostats and now we need toknow how long does it take for the water heater to heat up the cold water? Hot Water Heater Power Outage

If you installed a mis-matched electric water heater element it may indeed be overheating. Other link: Test electricity to water heater Larger image ✔ ECO reset keeps tripping Quick answer: Replace both thermostats, test elements. All posts now gluten free and contain no trans fats. navigate here I disconnect wires from each element, then I test continuity of the element.

Action: Check that factory insulation is installed over thermostats, and has not been removed 4) Look that thermostat is sitting flat against tank. How To Tell If Electric Water Heater Is Working Be sure and turn your power off. I went to my walk in closet.

You can only upload photos smaller than 5 MB.

Put insulation back over parts. Replace part that wire is connected to. the extra wiring is resistance of and unto itself, i.e. Reset Button On Hot Water Heater Won't Reset Of course the heating elements can be tested to see which is burned out (open, or infinite resistance) or shorted (zero resistance), as we describe in detail at Electric Water Heater

The breaker switches should be firmly in the ON position. It would lose energy to an unused branch only do to leakage which is minor and not a logical part of the problem. If reset is not tripped out, then reset is not problem. his comment is here Below we show how to find the thermostat control and reset switch for an electric water heater.

Answer Questions I need help buying my new snowblower, can you help? Special Offer: Carson Dunlop Associates offers InspectAPedia readers in the U.S.A. hmicda · 8 years ago 0 Thumbs up 1 Thumbs down Comment Add a comment Submit · just now Report Abuse Add your answer No hot water after power outage. ECO can trip if water heater is wet from flood, leak or tank failure.

What should I do. If the element goes out on the bottom, what are the symtoms and what are the symtoms if the top element goes out?